Tracert should be the first tool used when a Windows technician needs a quick view of the route to a host, while PathPing is better when the problem looks like packet loss or unstable performance across several hops. Tracert is fast, simple, and useful for spotting where traffic stops. PathPing takes longer, but it adds loss statistics that make it stronger for proving where a network issue lives.
TLDR: Tracert shows the path packets take and the time each hop takes to respond. PathPing combines route tracing with packet loss testing, so it gives better evidence when latency spikes or drops appear. For example, a branch office with 40 users might show normal Tracert times, but PathPing could reveal 18% packet loss at hop 6, pointing to an ISP handoff. In practice, Tracert often takes under 30 seconds, while PathPing may take several minutes.
What the Tracert Command Does
Tracert, short for trace route, is a built-in Windows command used to show the path from one computer to another network destination. That destination may be a website, server, router, cloud app, firewall, or public IP address.
It works by sending packets with increasing TTL values. TTL means Time To Live. Each router along the path reduces that value. When the value reaches zero, the router sends a response back. Tracert uses those responses to list each hop.
A common command looks like this:
tracert example.com
The output usually shows:
- Hop number, showing the order of routers in the path.
- Three response times, measured in milliseconds.
- Router name or IP address, when available.
- Timeouts, shown as an asterisk, when no reply arrives.
Tracert is useful because it gives quick answers. If a server is unreachable, the technician can see whether traffic leaves the local network, reaches the ISP, or dies somewhere in between. The catch is that Tracert can look worse than the real connection. Some routers ignore or limit these probes, even while forwarding normal traffic just fine.
What PathPing Does Differently
PathPing is also built into Windows. It starts like Tracert by mapping the route to the destination. Then it sends packets to each hop for a longer period and calculates packet loss.
A basic command looks like this:
pathping example.com
PathPing output is slower because it collects more data. That extra wait can be annoying. It drives many technicians crazy that a simple test may take 3 to 5 minutes, especially during an outage call. Still, the result is often worth it.
PathPing reports:
- Latency between the source and each hop.
- Packet loss from the source to each hop.
- Packet loss between individual hops.
- Route details, similar to Tracert.
This makes PathPing stronger for slow connections, poor voice quality, video freezes, or cloud app timeouts. A route may be reachable, yet still bad. Tracert may not prove that. PathPing often can.
Tracert vs PathPing: Main Differences
| Feature | Tracert | PathPing |
|---|---|---|
| Main use | Shows route to destination | Shows route and packet loss |
| Speed | Fast | Slow |
| Best for | Quick reachability checks | Loss and stability checks |
| Detail level | Basic | More detailed |
| Skill level | Beginner friendly | Better for deeper diagnostics |
Tracert answers, “Where does the route go?” PathPing answers, “Where does the route perform badly?” That difference matters when support teams need proof instead of guesses.
When Tracert Is the Better Choice
Tracert is the better first step in many cases. It is quick and easy to read. It helps confirm whether a route exists at all.
Technicians often use Tracert when:
- A website or server cannot be reached.
- DNS appears to point to the wrong location.
- Traffic seems to stop after the local router.
- An ISP issue is suspected.
- A firewall or routing change may have broken access.
For faster results, the -d option can skip DNS lookups:
tracert -d 8.8.8.8
This often makes the test cleaner. It also removes delays caused by slow reverse DNS lookups. That matters when a technician is comparing several targets in a short window.
When PathPing Is the Better Choice
PathPing is better when the connection works but performs poorly. This includes cases where users complain that apps “randomly freeze” or calls “sound robotic.” Those complaints are vague. PathPing helps turn them into numbers.
PathPing is useful when:
- Users report intermittent drops.
- Remote desktop sessions lag or disconnect.
- VoIP calls have jitter, gaps, or distortion.
- Cloud apps load slowly at certain times.
- There is a need to compare packet loss across hops.
A result showing 0% loss through the internal network but 12% loss after the ISP gateway tells a clear story. The internal team can avoid blaming switches, Wi Fi, or servers without evidence. That saves time and reduces finger pointing.
Common Problems Reading Results
Both commands can be misunderstood. An asterisk in Tracert does not always mean the route is broken. Some routers simply refuse to answer ICMP probes. If later hops respond, traffic is still passing through.
High latency at one middle hop does not always prove a fault either. A router may give low priority to diagnostic replies while forwarding real traffic at normal speed. The final destination matters more than a single scary number in the middle.
PathPing has the same issue, but its loss data helps add context. If one hop shows loss but later hops show no loss, the hop may only be limiting replies. If the loss continues through all later hops, the problem is more likely real.
Useful Command Options
Windows includes several options that make both tools easier to use.
tracert -d hostnameskips name resolution.tracert -h 15 hostnamelimits the maximum hop count to 15.tracert -w 1000 hostnamesets the timeout to 1000 milliseconds.pathping -n hostnameskips reverse DNS lookups.pathping -q 50 hostnamesends 50 queries per hop.pathping -w 1000 hostnamesets the wait time per reply.
The -n or -d style options are often the simplest improvement. They reduce clutter and make results appear faster.
Practical Diagnostic Workflow
A clean workflow helps avoid wasted time. A Windows support team may follow this order:
- Ping the target to confirm basic reachability.
- Run Tracert to see where traffic goes.
- Run Tracert with DNS disabled if results are slow or messy.
- Run PathPing if latency or packet loss is suspected.
- Compare results from a working location and a failing location.
- Save output for ISP, firewall, or server teams.
This process keeps the first test fast and the second test evidence based. It also helps when several teams share responsibility for a connection.
FAQ
Is Tracert the same as Ping?
No. Ping checks whether a host responds and measures basic round trip time. Tracert shows the route traffic takes to reach that host.
Is PathPing better than Tracert?
PathPing is better for packet loss and stability checks. Tracert is better for quick route discovery. Neither fully replaces the other.
Why does Tracert show asterisks?
Asterisks mean no reply was received for that probe. The router may be blocking replies, rate limiting them, or the packet may have been dropped.
Why does PathPing take so long?
PathPing sends many probes to each hop so it can calculate packet loss. That extra testing takes time but gives more useful data.
Can Tracert or PathPing fix network problems?
No. They are diagnostic tools. They help identify where a problem may exist, but they do not repair routing, DNS, firewall, ISP, or hardware issues.
Which command should a technician run first?
Tracert should usually run first because it is faster. If the route exists but performance still feels poor, PathPing should run next.
